How To Bind A Corona 2.4Ghz DSSS Receiver.




What do you think about this video?

mbagawin: hi sir, how come my corona DSSS receiver after switching on the batt the light led is falsh twice and then gone. when i switch it back again it wont turn on. can you help? now all the thress receivers are not showing their led lights. are they defective?

cambridgekiwi: You are welcome - I actually tricked myself a few weekends back - my JR module stopped working in my 9x (9303) - the receiver would bind, do the rapid flashes - but then not lock up. It worked perfectly the last time I used it in a different model. Took me a few days, but I finally had to give myself a slap on the back of my head ... what's Corona's first instruction... turn your transmitter on to PPM mode... Doh! SPCM doesn't work!

cambridgekiwi: Yes that's right, you can connect the power supply to any channel, so long as the plug is around the right way, be very careful of this with the small 3 or 4 channel receivers. Basically the power supply rails inside the receiver are all common, so it is a good idea not to short any of the other terminal pins while the battery is connected too! As for wire size, that depends on how much weight you want or need to carry - the bigger, heavier or faster the model, the bigger you will likely need.

cambridgekiwi: Sorry, I never saw this question to answer it - my apologies. Follow the proceedure again as per the video, the two flashes is the first stage of binding, it could be that the button is pressed inside the reciever causing it to try and bind all the time. The transmitter should only be turned on first when you are binding, every other time, it should be receiver first - hope this helps.

cambridgekiwi: I don't use the RP6D1's as they are not 2.4ghz receivers. Most probably you have solved the problem by now, otherwise I would suggest downloading the instructions for binding from the Corona site, and if you still have issues, contact them via Skype. The address for help is on their website.

nachom0: Hello!!! I have a few questions, can you please reply these? 1- Can I put the power connector in any channel of the receiver before the bind process (or there is a dedicated channel?)? 2- what size of wire I need in order to use 4 or 5 NiMh cells? 3- I have a flying win: Where can I connect the power connector (from battery) and the servo connectors? Thank you very much!!

Thomas Edmonds: Hi Nachom0, You can plug the battery to any of the eight channels that you are not using (usually ch 8). The signal wire (orange or yellow) goes to the top, the red (+) to the middle, and the black (-) to the bottom on the Corona receiver.

cambridgekiwi: @arcdirect Hey, no worries... actually, I am really surpirzed how "watched" this little video has been. I sell the Corona Gear in New Zealand, and I made the vid as a helper for those who I sold the system to, since the instructions in the box were a little difficult to follow. Pleased you have got your system going, i'm in the process of converting over to their latest FHSS system with Telemetry... still very new on the market, only available in a few places at the moment.

davereap: thanks for that, I couldnt remember the sequence, ive a module in my futaba..and the principle is exactly the same..

Angel Sion: Thank you was clear for me now.

Rating:
How to Bind a Corona 2.4Ghz DSSS receiver. 5 out of 5

Shared by Others

How to Bind a Corona 2.4Ghz DSSS receiver.
How to Bind a Corona 2.4Ghz DSSS receiver.
Review: Corona 2.4GHz DSSS DIY kit
Review: Corona 2.4GHz DSSS DIY kit
Hitec Optic 6 + Corona 2.4Ghz DIY Module & RX DSSS
Hitec Optic 6 + Corona 2.4Ghz DIY Module & RX DSSS
Futaba 9c vs CORONA 2.4GHZ module_Setigns for receivers
Futaba 9c vs CORONA 2.4GHZ module_Setigns for receivers
FrSky 2.4GHz spread spectrum RC review
FrSky 2.4GHz spread spectrum RC review
Turnigy 9X 2.4GHz radio control system Version 2 review (Part 1)
Turnigy 9X 2.4GHz radio control system Version 2 review (Part 1)
Turnigy 9X Corona FHSS 2.4GHz RC system has a problem
Turnigy 9X Corona FHSS 2.4GHz RC system has a problem
Review: Hitec Spectra AFHSS 2.4GHz receiver and Optima 7 module (part 1)
Review: Hitec Spectra AFHSS 2.4GHz receiver and Optima 7 module (part 1)
Convert JR Propo X-378 RC Radio to work with 2.4GHz Corona Module
Convert JR Propo X-378 RC Radio to work with 2.4GHz Corona Module
Review: Hitec Spectra AFHSS 2.4GHz receiver and module (part 3)
Review: Hitec Spectra AFHSS 2.4GHz receiver and module (part 3)
Review: The JR DSMJ FHSS 2.4GHz RC module and receiver.
Review: The JR DSMJ FHSS 2.4GHz RC module and receiver.
Futaba Attack 2.4 (upgraded with Corona 2.4 system)
Futaba Attack 2.4 (upgraded with Corona 2.4 system)
FrSky V8HT 2.4Ghz DIY Module Installation and Binding
FrSky V8HT 2.4Ghz DIY Module Installation and Binding
Review: Hitec Spectra AFHSS 2.4GHz receiver and Optima 7 module (part 2)
Review: Hitec Spectra AFHSS 2.4GHz receiver and Optima 7 module (part 2)
Corona DSSS V2 servo movement
Corona DSSS V2 servo movement
5 Channel Micro Parkflyer Receiver (Compatible with Hitec 2.4GHz A-FHSS)
5 Channel Micro Parkflyer Receiver (Compatible with Hitec 2.4GHz A-FHSS)
Flight test: FrSky 2.4GHz RC module/receiver
Flight test: FrSky 2.4GHz RC module/receiver
RC Bind Turnigy 9X V2 with HK TR6A V2 6Ch 2.4GHz rx (with original soundtrack)
RC Bind Turnigy 9X V2 with HK TR6A V2 6Ch 2.4GHz rx (with original soundtrack)
Futaba 6EX 6-Channel 2.4GHz Transmitter-Receiver
Futaba 6EX 6-Channel 2.4GHz Transmitter-Receiver

Featured Video