Joe Bagliere: You're the smartest kid alive. THANK YOU! MY HERO.
Madiba Donsmiffy: how do you remove a jammed peice of paper on a cannon mp240
Sol Panduro: Thanks!! my printer is working now!!!
Ashley Fleischman: still getting P 7 ERROR HOW DO i FIX
Ashley Fleischman: what do you do to fix the problem when it says the ink absorber is full. It will not allow anything to print. I a,so did your re set as shown above but that did not change anything as far as the problem I am getting with ink absorber.
Julio Rodriguez: how do you clean/empty ink absorber
Shuhag121: E05 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed proper
Error Code E05 Canon MP258 may solve by the following steps. 1. Press Stop/Reset button for 5 seconds. 2. After five seconds release the button. 3. Now your printer will start its process and it is.
If not reply again and I will find a solution for you.
Shirley Severns: I tried your suggestion but it didn't work. I am getting an E 0 5 flashing on my printer and I can't get it to print or scan or do anything. It says the ink is not recognized but it is canon ink cartridge, brand new. Please help....lol
Debbie M: Thank you. I just picked this printer up on Craigslist and needed help. The black ink light is on so I need to figure out how to replace the ink but this worked great and your instructions were clear. Thanks again!
rhonda sandhu: Hi Shuhag
I have tried your instruction but still have a number 1 showing. I have recently put new ink cartridges in but cannot get them to work. Can you give me any advice on this. Many thanks
Charles Perry Sutherland: Thanks so much. That worked for my Canon MP250. Yeahhhh.
Damera Arunkumar: Hello shuhag iam getting light blinks after refilling the ink in catridge how do i stop that blinking.
Monaian Ian: what does the E05 error code mean ?
Калян Смерч: пагано видно
Dominic Rocco: I got one of these but when I go to print its telling me no color ink recognize. I need color ink to print this to? I only bought black.
MrJhonygonzalez: Ihave the same problem that shivika, do the steps in the video and still doesn't work.,. please help me.. in the little screen of the printer blin a 5 and an E
Shuhag121: 1. The 8 error code just means that the ink absorber is full and needs to be replaced.
2.When cartridges move to centre position after lid is opened, remove and replace each cartridge. The chip light should flash as each cartridge is installed, those that do not flash have dead chips and need to be replaced.
Shuhag121: If you do the steps in my video and after that it still doesn't work, then reply again and I'll make a video of it maybe or tell you what to do
Shuhag121: No it doesn't need to be connected to the pc but you can if you want to.
Pawel Pieta: should it be connected to the pc while doing it ?
babybronc10: couldn't get it to work. still get error 5200 and P 8 flashing on my printer
Sushi Wasabi: 0 doesn't show up on mine. WTF?
Shuhag121: did u try the steps in the video
Shivika gurusinghe: I have problem with my cannon pixma mp240 printer. Since the two cartridges are not been inserted I find difficult to use my scanner. How can I use the scanner without the cartridges.
kchiang4: Did the steps given: no 0 appears, "Alarm" indicator flashing along with "Color ink" flashing as well (I just put in a new ink cartridge not too long ago), after all that, paper comes out like yours, except E5 error is still there. Already updated the driver and installed new software... but I still cannot scan documents with this MP240 printer...
woopsme: Awesome video man. I've got a question, will the E31 error code and/or color ink green light prevent me from scanning? I used to be able to scan and now it just gives the E31 error code when I press scan. Thanks
hinetuaeu: Don't believe it - it worked!! Cheers buddy
Fawad Akhtar: HI, do you have any idea how to reset Pixma MX525?
Please do lemme know thanks
Luís Vieira: Hi! is it the same with the mp260?
D. Williams: I did the steps and it all was ready to print. Unfortunately it went right back to flashing P8 and Error Code 5200 is on the screen reading unable to print cartridges are low level. I dont understand why it says that when they are brand new ink. Can you still help me?
Nan Vidal: You are my hero!!!! Thanks for your helpful tutorial
Tahrima Tarin: Thanks a lot it worked great for me
good job well done :)
A. Cunningham: Brilliant job, clear, understandable and I fixed my printer!!!! Well done.
Christopher Dunn: Thank you so much, The quality wasn't coming out due to the set up at first and was starting to panic. But thanks to your help it has printed perfect. I needed this information quickly as writing a CV for a job and the information you have put on here has been very helpful. Thank you again :)
steven irvin: THANK YOU
HMTMKM0X: tried that too...still get error code 3
HMTMKM0X: still getting the error code 3 and there is no paper jammed
MyGlowingMouth: Thanks, finally can scan without cartridges now! Great help!
Joshua Lizama: My printer isn't working after reseting it, the alarm blinking light is on and there is a P followed by the letter 8 showin up in the green light, can you help me fix it
Vickie Minter: I used this for my Canon MP250 and it also worked. Thank you for your help.
vessel4thelordjesus: thanks its worked. God bless
Fabiola Mendonça: Deus te abençoe criança!
rony88771: Thanks a lot mate , it really helped
CiprianXxZz: thx man:)
gimbha: Hi there, this is great, however when I do the reset no "0" comes up -- instead, the "alarm" light comes on and blinks. Any other ideas?
Shuhag121: Do the reset process in the video above and it should hopefully work
If not reply again and I'll see what I can do
Brandon fotheringill: after changed ink cartridge alarm light is blinking & can't copy
Cupid_stunts: have you fixed it? if, tell me how, cause i´ve the same problem...
Shuhag121: 1. Get a cardboard that will fit through the paper sucker thing (A4 cardboard is good:) )
2. Take all the paper out of the printer.
3. Shove the cardboard through the paper sucker thing until it comes out the other end.
(You might get tiny bits of crunched up paper or rubber out the other end as well.)
4. Do the reset process in my video and it should work
If not leave a reply and I will make a video of it.